- Capacitor Shield ? - 6 Updates
| etpm@whidbey.com: Nov 06 09:21AM -0800 >with 1 second spaced stills setting, recording to SD, to suspend over >the banch for when disassembling the next complicated mechanism, with no >exploded views in a manual That is a GREAT idea! I am now going to buy one. I do mostly mechanical stuff and even though I try to document everything I take apart I sometimes make a misteak. Thanks for posting your idea. Eric |
| N_Cook <diverse@tcp.co.uk>: Nov 06 05:52PM > mechanical stuff and even though I try to document everything I take > apart I sometimes make a misteak. Thanks for posting your idea. > Eric I've always been in the habit of felt-tip marking the joins of plates , ith a straight line across the join, before taking apart. And small boxes for sub-sections that go together. But even then I sometimes end up with unplaced parts. This dash-cam is Nikkai ER-130V. Make sure whatever you get comes with a viewer that allows selecting single frames |
| etpm@whidbey.com: Nov 06 12:03PM -0800 >up with unplaced parts. >This dash-cam is Nikkai ER-130V. Make sure whatever you get comes with a >viewer that allows selecting single frames I would have though that viewing single frames would be standard. Thanks for the heads up. Lots of the stuff I take apart has to be cleaned and this removes marks. Right now I try to take pictures but it can be a hassle. But just being able to hold an assembly in focus and not have to stop and take a picture would be great. Eric |
| Cydrome Leader <presence@MUNGEpanix.com>: Nov 06 09:18PM > https://dl.dropboxusercontent.com/u/29948706/KR-4070%20Caps.jpg > In a Kenwood receiver. It is steel, not aluminum. > What is its purpose ? looks weird, like an afterthough. Is there anything fastening the metal "shield" to the PCB below? Maybe they had that board rattle apart of break loose with the large caps and bridge rectifier attached to it. I'd almost expect the caps in something of that age to be screwed down with a collar and have wire wrap terminals or something weird like they did then. There's quite a bit of stress on the parts in those big heavy receivers as they get shipped across the world. Heard from one guy that sent to the factory where they had audio gear manufactured that the power transformers were all being screwed down wrong, with the spring washer in the wrong place. He told the production people that's not going to work, but they ignored that. By the time the stuff made it to the US, every transformer busted free. It all had to be reworked in the US. Whoops. |
| Trevor Wilson <trevor@SPAMBLOCKrageaudio.com.au>: Nov 07 08:19AM +1100 > https://dl.dropboxusercontent.com/u/29948706/KR-4070%20Caps.jpg > In a Kenwood receiver. It is steel, not aluminum. > What is its purpose ? **Looks suspiciously like a DIY'er addition to me. The only time I've ever seen covers on caps are ones on old mains suppression caps. -- Trevor Wilson www.rageaudio.com.au --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus |
| Chuck <chuck@mydeja.net>: Nov 06 04:01PM -0600 On Fri, 6 Nov 2015 10:43:40 -0500, "Tom Miller" >I there a fan for forced air cooling? If so, maybe it is for directing >cooling air? >Just another guess. No there wasn't. This receiver is from the late 70's and had a more than adequate heat sink. Worked on quite a few of these back in the day and I don't remember this piece of metal. --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus |
| You received this digest because you're subscribed to updates for this group. You can change your settings on the group membership page. To unsubscribe from this group and stop receiving emails from it send an email to sci.electronics.repair+unsubscribe@googlegroups.com. |
No Response to "Digest for sci.electronics.repair@googlegroups.com - 6 updates in 1 topic"
Post a Comment